Coin purse #3

Coin purse project          

 Note:- this coin purse project have four pocket, the original design was for two pocket version. 

This coin purse project is an extension of the coin purse #2 (26th Oct 2018) and coin purse #1 (19th Oct 2018).

In this project is to share some challenges.

Tools shown for burnishing edge

Pre assembly of part which require burnishing on the edge (facing up position).

*Note:- use a chop stick to help hold work piece in position to make it easier to do burnishing work. This is especially beneficial for soft or thin leather material.  

** Have an idea to use aluminum bracket for this process and work in progress.


Top view on the middle layer



Edge of coin purse



Marking wheel for pricking hole

Use an awl to prick hole

sew bottom edge of center layer

Tool and materials for aligning
punch hole on button


Temporary add double sided tape to hold flap
in position

Press and align flap part on button
for marking position.

Make mark by pressing over button

Punch hole for flap

One way to minimize glue from spreading over it broder edge line. Use a scrap leather with clean edge when apply glue.
This is one simple tips when apply glue on leather surface.


Update 26th Nov 2018

One of finish product on coin purse with 4 pocket.

 One design on coin purse.
Rear view of coin purse. simple strap












The sole purpose of adding a simple strap was to make it easier to retrieve this coin purse from a bag. It allow user to quickly distinguish and pull it out. As the coin inside is quite heavy when fully loaded.





Side view


Both strap end are just a simple knot terminated for ease
to replace them when required.
Peek into inside of coin purse



    = = = = = =  End of document = = = = = =

Comments

Post a Comment

Popular posts from this blog

Card Holder #3 Part 2

Image
Card Holder with RFID casing 👴            Purchase a automatic pop up aluminium wallet attached to leather card holder. This is a preview of what the of possibility to combining two product into a single user friendlier card holder and RFID case. One example where card holder attached with automatic pop up  aluminium wallet Possible position for automatic pop up casing View of pop up lever With card in pop up position. View from different angle The challenge now is how to attach this RFID automatic pop up casing to card holder. Need to think a better way to attach them together... please wait as work in progress... = = = = = = = = End of document = = = =  happy viewing and relax
Read more

New idea Coin Purse

Image
Coin Purse project.. This started off as a project suggested by a friend.. So let start off with the design, cut out pattern for a very simple but practical for small and medium size coin purse. Front view of coin pruse End product of project coin purse Rear view of project Sharing sticthing used on project Raw material for coin purse project, approx 8cm width Cut out material to requirement = = = = = = = = next step  = = = = = = =  Next is to cut round corner with coin as guide. Ensure your cutter is sharpen before start work. Refer short video on how the round corner is done. Draw line to mark point for ease to apply glue to edge = = = = = = = = = =  Next step = = = = = = = = Fold the flap and use a pointed awl to mark place for button location. Use the hole punch to mark over hole for alignment. Once confirm punch hole. = = = = = = * * * = = = = = = Using punch to make a light impression to confirm before punch hole process Once confirm punch a hole for button Add post...
Read more

Coin Purse

Image
18th April 2018 .                    Today start a fresh with new blog page to make it easier to navigate. I'am still learning how to use this blogspot and update new project idea, tips and learn from our mistake to improve. The old way I use to append my blog spot make not so easy to know if there is new project being updated. Sorry for making my blogspot not so user friendlier easy to read and discover new items. Update 24th April 2018. Various design , shape and different leather material, thread type and color are used.All these project use to conceal the button head between two leather. Have to be careful not to button to close to edge as it will make stitching a bit more challenging. This was done in preparation for as gift to close friends. Enhance natural "defective" found on leather as part of design pattern. Interesting way to explore it benefit base on it unique pattern. =======================++++++++++++++===================...
Read more