bodner043

Today experimenting on various way to stitch O ring or loop pattern for luggage tag strap. Sharing best practice for making O ring or loop and try some pattern when stitching. Experimenting with different pattern on stitching. Make loop for strap . Another strap design by using veg tan leather. End of document...

Fabricate strap for luggage tag project. You can try search feature on blog or quick reference base on these past post. *refer to  Overall view on project post dated 13th Aug 2018 *refer to  Past Project   post dated 29th July 2018 *refer to Luggage Tage Project post dated 18th Apr 2018 . Have a simple tips to share when try to cut long narrow leather materials for luggage tag strap. Add a thin strip of double sided tape on cutting mat to help keep leather in place.  This one way it minimize the soft leather from moving around during cutting process. It is especially challenging for longer material. This more challenging if the leather material is soft or not so rigid. It easy to remove the double sided tape after use. Punch oblong hole for belt buckle. * Tips to lightly tap the oblong punch mark to confirm location before punch. Note the pin mark also assist in check alignment and it center position. How to align oblong punch to strap, note a small pin ma...

Slight different design for this pencil case project. *note :- See another old project date 17th June 2017 (trying make small gift)  for more details on pencil case shown below. A simple gift to make and can be creative and customize to project needs. It will be better to burnish the middle and front layer edge ( top edge)  before assemble project. As it make it easier work later. The edge use a brown colour paint marker to even the colour difference. One comment, this pencil case is slightly shorter for small ruler (6 inch ruler). End of document

Today try improvement and slight design difference for a DVD pouch casing. * Note:-  You can refer to previous post (dated 18th July , title of post New project DVD pouch #1) End of document

          Kids leather slipper       Trying new skill and project, a basic kid slipper.       This new project was in the mind for quite sometime. Reading from YouTube and Pinterest for more inform, idea, tips and learning some new skill for making a basic kid slipper along the way. Step to start project Finally it done. But notice there is alot to learn after realizing there are some mistake in term of sequence and lack foresight, and still in learning stage/phase. Sometime we learn faster after see the shortcoming and than try to improve on the next project. 1) Uneven stitching work between insole and leather. 2) The in sole is the last part to gule 3) The skill to trim the multiple layer need practice 4) Add lining for the slipper edge. Update on 12th Nov 2018. Check on slipper status.. good so far. End of document.

Continue with badge tag or ID tag project. Sharing some completed project for badge tag or ID tag. Best practice and tips on project which two different type of leather. A softer leather will produce strange result, where by the softer leather surface will wrinkle or uneven surface. Hence it need care during stitching phase.  A friend share one commercial badge tag for comparison and try to improve or incorporate feature such as simple and quick design. The idea is to customize for each individual needs and requirement. One user prefer just the badge tag with following feature. 1) Sturdy strap leads 2) Have additional pocket for daily credit card or loyalty card, access card. 3) Some like a more broader base badge tag 4) Other like to incorporate link to rectardable layward hook up. 5) Other like a simple key ring termination. Side by side comparison and get estimate dimension for badge tag. Comparison and take note to add a rear pocket for holding credit card or access card. More ...

Badge tag project Update 5th Sept 2018 to compare old and new design badge tag.  Front view of badge tag. On the left is the new badge tag, on the right is an old badge tag. Rear view of the badge tag. You will notice the new badge tag rear layer is a firmer leather to support the front layer. This is some thing simple and new to try out project, badge tag for ID card size of 8.5 cm and 5.5 cm.  Use an ID card , or old credit card size template to prepare for leather material. Cut project leather for width approximately 7.5 cm. Cut the height of leather of approximately 11.5cm. Cut two leather of same dimension, 7.5 cm x 11.5 cm. Measure to cut a rectangular hole base on the template ID card size, slightly smaller approx 5mm from edge of template. The inner line marking is where to cut off.  The backing layer need to cut a slit hole to accommodate for inserting the crd  Gule both layer together  Rear view of project  Height of cut off is approximately 7.5 c...