Card Holder #2


          Card holder project.

This project was request by a friend on 18th Jan 2018.
But was put on hold as there were other urgent job on hand.

There is three different design for card holder.

Now revisit this project again for card holder (with ample space for RFID case holder not shown here).
This is a sample card holder provide by friend, hence taken some measurement.

Card Holder front view

Rear view in open position



Overall measurement view



Note:- Work in progress, sorry for the inconvenience.

Update 16th Nov 2018.
Still not ready yet as searching material of suitable thickness... please wait and thank you for patience.


Update 23rd Nov 2018.
Was busy with work life, week end have opportunity to continue project.



Draw drain line for punch hole

Temporary remove layer to add button

Add a strap with button


Strap hidden

















Cut slot for strap

Rear view of project


Stitch the strap to outer layer

Pre assemble by punch hole
for outer and inner layer

Cut slotted line for strap to
sit in

Mark line for punch hole


 Inside view of finish product


Out side view.














Rear outside view

Update 24th Nov 2018.

Another card holder of different material and bigger flap..


Bigger design flap


Layout various part of project

Punch hole for cutting slot line

 reduce thickness by remove part of the leather
Sand paper surface before gule


Cover the button metal part




               = * = * = * = * =

Slightly different design with different leather material for this project. Try use a softer material on inside.



Layout material for proejct

 Mark position for button



Sew one of the edge (flap)

 Align and position coin for cutting round edge
Prepare for punch hole for button


one way to cut curve line






Front view of project

Rear view of project
Inside view of project
Three design for card holder.



Update 28th Nov 2018

Provide additional information on RFID casing and card holder as how it is interface and attached.
It give clear view how they are interface and works together.

 Side view to show how the RFID casing attached to card holder.











Another angle to view card holder with one side of edge attached
a RFID casing which make possible to store on card holder design.


RFID Automatic Pop Up Card Holder Aluminum Alloy dimension is 9.6cm x 6.3 cm x 1 cm.


= = = = = =  End of Document = = = = = =

Comments

Post a Comment

Popular posts from this blog

Card Holder #3 Part 2

Image
Card Holder with RFID casing 👴            Purchase a automatic pop up aluminium wallet attached to leather card holder. This is a preview of what the of possibility to combining two product into a single user friendlier card holder and RFID case. One example where card holder attached with automatic pop up  aluminium wallet Possible position for automatic pop up casing View of pop up lever With card in pop up position. View from different angle The challenge now is how to attach this RFID automatic pop up casing to card holder. Need to think a better way to attach them together... please wait as work in progress... = = = = = = = = End of document = = = =  happy viewing and relax
Read more

New idea Coin Purse

Image
Coin Purse project.. This started off as a project suggested by a friend.. So let start off with the design, cut out pattern for a very simple but practical for small and medium size coin purse. Front view of coin pruse End product of project coin purse Rear view of project Sharing sticthing used on project Raw material for coin purse project, approx 8cm width Cut out material to requirement = = = = = = = = next step  = = = = = = =  Next is to cut round corner with coin as guide. Ensure your cutter is sharpen before start work. Refer short video on how the round corner is done. Draw line to mark point for ease to apply glue to edge = = = = = = = = = =  Next step = = = = = = = = Fold the flap and use a pointed awl to mark place for button location. Use the hole punch to mark over hole for alignment. Once confirm punch hole. = = = = = = * * * = = = = = = Using punch to make a light impression to confirm before punch hole process Once confirm punch a hole for button Add post...
Read more

Coin Purse

Image
18th April 2018 .                    Today start a fresh with new blog page to make it easier to navigate. I'am still learning how to use this blogspot and update new project idea, tips and learn from our mistake to improve. The old way I use to append my blog spot make not so easy to know if there is new project being updated. Sorry for making my blogspot not so user friendlier easy to read and discover new items. Update 24th April 2018. Various design , shape and different leather material, thread type and color are used.All these project use to conceal the button head between two leather. Have to be careful not to button to close to edge as it will make stitching a bit more challenging. This was done in preparation for as gift to close friends. Enhance natural "defective" found on leather as part of design pattern. Interesting way to explore it benefit base on it unique pattern. =======================++++++++++++++===================...
Read more